Rolling bearings - Needle roller bearings for automotive transmission
1 Scope
This document specifies the code method, structural type, overall dimension, technical requirements, testing methods, inspection rules, markings, and rustproof packaging for needle roller bearings for automotive transmissions.
This document is applicable to the manufacturing of needle roller bearings for automotive transmissions (hereinafter referred to as "bearings").
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 272-2017 Rolling bearings Identification code
GB/T 307.1-2017 Rolling bearings - Radial bearings - Geometrical product specification (GPS) and tolerance values
GB/T 307.2-2005 Rolling bearings - Measuring and gauging principles and methods
GB/T 307.3-2017 Rolling bearings - General technical regulations
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T4199-2003 Rolling bearings - Tolerances - Definitions
GB/T 4604.1-2012 Rolling bearings - Internal clearance - Part 1: Radial internal clearance for radial bearings
GB/T 4605-2003 Rolling bearings - Thrust needle roller and cage assemblies, thrust washers
GB/T 6930-2024 Rolling bearings - Vocabulary
GB/T 7811-2015 Rolling bearings - Symbols for physical quantities
GB/T 8597-2013 Rolling bearings - Rust proof packaging
GB/T 20056-2015 Rolling bearings - Radial needle roller and cage assemblies - Boundary dimensions and tolerances
GB/T 24605-2009 Rolling bearings - Marking for products
GB/T 24607-2023 Rolling bearings - Test and assessment for life and reliability
GB/T 25769-2010 Rolling bearings - Measuring methods for radial internal clearance
GB/T 28268-2012 Rolling bearings - Specifications of pressed cages
GB/T 33624-2017 Rolling bearings - Test and assessment methods for cleanliness
GB/T 34891-2017 Rolling bearings - Parts made from high-carbon chromium bearing steels - Specifications for heat treatment
JB/T 6639-2015 Rolling bearings - Rubber seals reinforced with a sheet steel insert - Specifications
JB/T 6641-2017 Rolling bearings - Residual magnetism and its assessment method
JB/T 7048-2011 Rolling bearings - Engineering plastie cages - Specification
JB/T 7051-2006 Rolling bearing parts - Methods for the measurement and assessment of surface roughness
JB/T 7363-2023 Rolling bearings - Parts made from carbonitriding - Specifications for heat-treatment
JB/T 8211-2023 Rolling bearings - Thrust cylindrical roller and cage assemblies, thrust washers
JB/T 8878-2011 Rolling bearings - Drawn cup needle roller bearings - Specifications
JB/T 8881-2020 Rolling bearings - Parts made from carburizing bearing steels - Specifications for heat treatment
JB/T 10336-2017 Rolling bearings - Additional specifications
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 4199-2003 and GB/T 6930-2024 apply.
4 Symbols
For the purposes of this document, the symbols given in GB/T 4199-2003 and GB/T 7811-2015 and the following apply.
B1: The distance from the inner side of the barrier to the small end face
d1: Diameter of inner raceway
T: Height of thrust needle bearing assembly
Contents
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Classification of needle roller bearings for transmission
6 Identification codes
7 Structural type
8 Overall dimension
9 Technical requirements
10 Testing methods
11 Inspection rules
12 Marking
13 Rustproof packaging
Annex A (Informative) Technical specifications for the fit between the shaft, bearing seat, and needle roller bearing
Bibliography
