標準編號:	GB/T 25774.2-2016
中文名稱:	焊接材料的檢驗 第2部分：鋼的單面單道焊和雙面單道焊焊接接頭力學性能試樣的制備及檢驗
英文名稱:	Test methods for welding consumables―Part 2:Preparation of single-run and two-run technique test specimens in steel
中標分類:	J33    焊接與切割
行業分類:	GB    國家標準
ICS分類:	25.160.20 25.160.20    焊接消耗品 25.160.20
發布機構:	中華人民共和國國家質量監督檢驗檢疫總局 中國國家標準化管理委員會
發布日期:	2016-02-24
實施日期:	2016-9-1
標準狀態:	superseded
被新標準替代:	GB/T 25774.2-2023 焊接材料的檢驗 第2部分：鋼的單面單道焊和雙面單道焊焊接接頭力學性能試樣的制備
被替代日期:	2024-6-1
翻譯語言:	英文
文件格式:	PDF
中文字符數:	11000 字
翻譯價格(元):	660.0
交付時間:	付款后 1 個工作日

GB/T 25774.2-2016 Test methods for welding consumables - Part 2: Preparation of single-run and two-run technique test specimens in steel 1 Scope This part of GB/T 25774 specifies the preparation and inspection methods of tensile specimens and impact specimens for single-run welding and double-run welding joints of steel welding consumables. This part is applicable to the determination of joint strength and toughness of arc welding consumables of steel under single-run welding and double-run welding conditions. This part is not applicable to electroslag welding and gas-electric vertical welding. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 2650 Impact test methods on welded joints (GB/T 2650-2008, ISO 9016: 2001, IDT) GB/T 2651 Tensile test method on welded joints (GB/T 2651-2008, ISO 4136: 2001, IDT) GB/T 18591 Welding - Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature (GB/T 18591-2001. Idt ISO 13916: 1996) 3 General Principles The welding consumables to be tested are representative products that the manufacturer needs to classify or inspect. Tensile and impact specimens of welded joints are prepared according to the following requirements. 4 Test base materials The base materials used for the test shall meet the requirements of the corresponding welding consumables product standard. 5 Preparation of specimens The test plates shall be reversed deformed or restrained before welding to prevent angular deformation, and the specimens are not allowed to be corrected after welding. As for single-run welding, a backing plate may be added on the back. Arc starting plate and arc closing plate can be used for welding, see Table1.

Foreword i 1 Scope 2 Normative references 3 General Principles 4 Test base materials 5 Preparation of specimens 6 Welding conditions 7 Heat treatment 8 Sampling position, specimen dimension and test 9 Re-inspection 10 Test report