標準編號:	TB/T 1492-2002
中文名稱:	鐵道車輛制動機單車試驗方法
英文名稱:	The method of single car for railway passenger car and wagon brake
中標分類:	S32    制動系統
行業分類:	TB    鐵路運輸行業標準
ICS分類:	45.060.20 45.060.20    車輛 45.060.20
發布機構:	中華人民共和國鐵道部
發布日期:	2002-05-17
實施日期:	2002-12-1
標準狀態:	superseded
被新標準替代:	TB/T 1492-2017 鐵道車輛制動機單車試驗
被替代日期:	2018-5-1
替代舊標準:	TB/T 1492-1983 鐵路客貨車制動機單車試驗方法 TB/T 2401-1993 裝有閘瓦間隙調整器的貨車制動機單車試驗方法
翻譯語言:	英文
文件格式:	PDF
中文字符數:	10000 字
翻譯價格(元):	600.0
交付時間:	付款后 1 個工作日

1 Scope This standard specifies the single car test methods for installed brakes of 104, F8, GK, 103 and 120 cars. This standard is applicable to the railway passenger car and wagon equipped with air brake, as well as those equipped with electro-pneumatic brake. 2 Normative References The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. For any undated references, the latest edition of the document referred to applies. TB/T 1901-1999 Technical Specifications for Assembling of Vehicle Braking Device 3 Test Requirements 3.1 Single car test for railway passenger car and wagon brake (hereafter referred to as “single car test”) may be conducted only if the brake assembly meets the requirements for railway passenger car and wagon as specified TB/T 1901-1999. 3.2 Where two or more sets of brakes are installed in one car, each set shall undergo single car test. 3.3 During single car test, other pneumatic devices installed in the car shall be under the car-operating state and shall not influence the normal function of brake. Single car test shall be conducted under empty vehicle state. For the purpose of the loaded car test or single car test for empty/loaded car equipped with empty and loaded automatic adjustment equipment, the relevant requirements shall apply. 3.5 The single car test for railway passenger car and wagon brake shall be carried out with single car tester for passenger car and for wagon respectively. The test pressure (hereafter referred to as constant pressure) shall be 600kPa and 500kPa respectively. 3.6 Single car tester shall be used to perform function inspection according to Appendix A. 3.7 For the purpose of single car test, double-needle or single-needle pressure gauge with measuring range of 0~1000kPa and precision grade of 1.5 shall be adopted and calibrated every three months. The single car tester collecting the pressure value by other means shall comply with the relevant requirements. 3.8 The rubber hose connecting the single car tester and the brake hose connector of tested car shall be 25mm in inner diameter and 1.5m~2m in length.

Foreword i 1 Scope 2 Normative References 3 Test Requirements 4 Test Preparation 5 Single Car Test Methods and Technical Requirements for Air Brake 6 Solenoid Valve Performance Test 7 Single Car Test Methods and Technical Requirements for Electro-pneumatic Brake Appendix A (Normative) Function Test Method for Single Car Tester