GB 17565-2022 General specifications for burglary-resistant security doors
1 Scope
This document specifies the grading, classification, labeling and technical requirements of burglary-resistant security doors, describes the test methods for burglary-resistant security doors, and determines the inspection rules for burglary-resistant security doors.
This document is applicable to the design, manufacture, testing and acceptance of burglary-resistant security doors and doors with similar burglary-resistant functions used in other important places.
2 Normative references
The following documents contain requirements which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 9286-2021 Paints and varnishes - Cross-cut test
GB 10409-2019 Burglary-resistant safes
GB 18580 Indoor decorating and refurbishing materials - Limit of formaldehyde emission of wood-based panels and finishing products
GA/T 73-2015 Burglary-resistant mechanical locks
GA 374-2019 Burglary-resistant electronic locks
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB 10409 and the following apply.
3.1
burglary-resistant security door
door that can undergo abnormal opening under certain conditions, has certain security protection performance and meets the corresponding burglary-resistant security class
Note: It is referred to as "security door".
?
3.2
burglary-resistant security class
security class of a security door divided according to the duration that the weakest link of the security door can undergo abnormal opening under the action of the specified destruction tool
3.3
protection surface
door leaf surface of a security door outside the protected area
3.4
locking bolt
bolt-like device with a certain strength that restrains the relative movement of the door leaf and the door frame
3.5
simple hard tool
all kinds of hardware tools with a length of less than or equal to 150 mm and a diameter of less than or equal to 25 mm
3.6
common hand tool
chisels, punches, wedges, screwdrivers, hacksaws, wrenches, pliers, hammers with a mass of less than or equal to 3.6 kg and prying tools with a length of less than or equal to 1.5 m and a diameter of less than or equal to 25 mm (or equivalent cross-sectional area)
[Source: GB 10409-2019, 3.16, modified]
3.7
portable electric tool
portable hand-held electric drills with a bit diameter of less than or equal to 12.7 mm and a power of less than or equal to 1,800 W; and portable electric impact hammers and pressurizing devices with a punch diameter of less than or equal to 25.4 mm and a power of less than or equal to 2,400 W
[Source: GB 10409-2019, 3.17]
3.8
specific portable electric tool
a general term for portable cutting machine, portable abrasive cutting wheel and electric saw
[Source: GB 10409-2019, 3.18]
3.8.1
portable cutting machine
hand-held cutting machine with high-speed cemented carbide-inlaid steel teeth, with a diameter of less than or equal to 203 mm, a power of less than or equal to 2,400 W and a speed of less than or equal to 8,000 r/min
[Source: GB 10409-2019, 3.18.1]
3.8.2
portable abrasive cutting wheel
electric hand-held disc abrasive cutting wheel with a grinding wheel diameter of less than or equal to 203 mm and thickness of less than or equal to 3.2 mm, a power of less than or equal to 2,400 W, and a speed of less than or equal to 8,000 r/min
[Source: GB 10409-2019, 3.18.2]
3.8.3
electric saw
a general term for circular saw, hole saw and reciprocating saw
[Source: GB 10409-2019, 3.18.3]
3.8.3.1
circular saw
a kind of electric saw with high-speed steel or cemented carbide-inlaid teeth, with a circular saw blade diameter of less than or equal to 203 mm, a power of less than or equal to 2,400 W, and a speed of less than or equal to 5,000 r/min
[Source: GB 10409-2019, 3.18.3.1]
3.8.3.2
hole saw
cylindrical saw device for cutting holes with high-speed steel or cemented carbide-inlaid teeth, with a hole diameter of less than or equal to 76 mm, for use together with portable hand-held electric drill
[Source: GB 10409-2019, 3.18.3.2, modified]
3.8.3.3
reciprocating saw
hand-held reciprocating saw device with high-speed steel or cemented carbide-inlaid teeth, with a power of less than or equal to 2,400 W
[Source: GB 10409-2019, 3.18.3.3, modified]
3.9
net working time
actual destructive attack time, excluding test preparation time and possible delays during the test
[Source: GB 10409-2019, 3.13]
3.10
615 cm2 opening
rectangular opening with a minimum side length of 152 mm, or circular opening with a diameter of 281 mm, or an isosceles right triangle opening with a hypotenuse length of 497 mm
Foreword II
Introduction V
1 Scope
2 Normative references
3 Terms and definitions
4 Grading, classification and labeling
5 Technical requirements
6 Test methods
7 Inspection rules
7.1 Type inspection
7.2 End-of-manufacturing inspection
7.3 Inspection items
7.4 Inspection and judgment rules
Annex A (Normative) Classification and related dimensional requirements for universal locks
Figure 1 Schematic diagram for frame-leaf lap width
Figure 2 Break-in resistance test
Figure 3 Soft impact performance test
Figure 4 Hoisting capacity test of hanging end
Figure 5 Impact to obstacle test
Figure A.1 Overall dimensions of lock body
Figure A.2 Overall dimensions of lock cylinder
Table 1 Burglary-resistant security classes
Table 2 Nominal thickness of steel plate
Table 3 Permissible negative deviation for steel plate thickness
Table 4 Tolerances for diagonal dimensions of door frame and leaf and tolerances for height and width of frame notch and door leaf
Table 5 Maximum variation in gap between door frame and leaf after the soft impact performance test of door leaf
Table 6 Items of type inspection and end-of-manufacturing inspection
Table A.1 Specifications, models and overall dimensions of lock body
Table A.2 Overall dimensions of lock cylinder
