標準編號:	GB/T 2662-2017
中文名稱:	棉服裝
英文名稱:	Clothes with fillings
中標分類:	Y76    服裝、服飾品
行業分類:	GB    國家標準
ICS分類:	61.020 61.020    服裝 61.020
發布機構:	中華人民共和國國家質量監督檢驗檢疫總局 中國國家標準化管理委員會
發布日期:	2017-05-12
實施日期:	2017-12-1
標準狀態:	valid
替代舊標準:	GB/T 2662-2008 棉服裝
翻譯語言:	英文
文件格式:	PDF
中文字符數:	14000 字
翻譯價格(元):	360.0
交付時間:	付款后 1 個工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. This standard is developed in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 2662-2008 Cotton Wadded Clothes and has the following main technical changes with respect to GB/T 2662-2008: ——The standard range is modified (see Chapter 1; Chapter 1 of 2008 edition); ——Normative references are modified and supplemented (see Chapter 2; Chapter 2 of 2008 edition); ——Requirements for the instructions for use of finished products are modified (see 3.1; 3.1 of 2008 edition); ——Requirements for raw materials are modified (see 3.3; 3.3 of 2008 edition); ——Requirements for appearance defects are modified (see 3.7; 3.7 of 2008 edition); ——Sewing requirements are modified (see 3.8; 3.8 of 2008 edition); ——Ironing requirements are modified (see 3.10; 3.10 of 2008 edition); ——Tables of physical and chemical performance are combined and their requirements are modified (see 3.11; 3.11 of 2008 edition); ——Shirts for children aged from more than 36 months to 14 years old are added and shall also comply with the requirements of GB 31701 (see 3.12); ——Requirements for inspection methods are modified and test methods for safety performance of children's clothing are added (see Chapter 4; Chapter 4 of 2008 edition); ——Requirements for inspection classification are modified (see 5.1; 5.1 of 2008 edition); ——Requirements for the judgement of appearance quality defect are modified (see Table 6 in 5.2.3; Table 11 in 5.2.3 of 2008 edition); ——The judgment rules are modified (see 5.4; 5.4 of 2008 edition); ——"Test methods for seam slippage" and "Schematic diagram for the sampling position for back crotch seam strength test" in annexes are deleted (see Annexes A and B of 2008 edition). This standard was proposed by the China National Textile and Apparel Council. This standard is under the jurisdiction of the National Technical Committee on Garments of Standardization Administration of China (SAC/TC 219). The previous editions of this standard are as follows: ——GB/T 2662-1981, GB/T 2662-1999, GB/T 2662-2008. Clothes with Fillings 1 Scope This standard specifies the requirements, inspection methods, inspection rules, marking, packaging, transportation and storage of clothes with fillings. This standard is applicable to mass-produced clothes with fillings taking woven with textile machine as main fabric, various natural fiber, chemical fiber and their blends as filling, or animal fur, fake fur and the like as lining or detachable lining. This standard is not applicable to the products containing down and feather in filling. This standard is not applicable to clothes for infants aged 36 months and below. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 250 Textiles - Tests for Colour Fastness - Grey Scale for Assessing Change in Colour GB/T 1335 (All Parts) Standard Sizing Systems for Garments GB/T 3921-2008 Textiles - Tests for Colour Fastness - Colour Fastness to Washing with Soap or Soap and Soda GB/T 4841.3 Colour Cards of Standard Depths for Dyeing with Dyestuffs 2/1, 1/3, 1/6, 1/12, 1/25 GB 5296.4 Instructions for Use of Products of Consumer Interest - Part 4: Textiles and Apparel GB/T 8170 Rules of Rounding off for Numerical Values & Expression and Judgement of Limiting Values GB/T 8427-2008 Textiles - Tests for Colour Fastness - Colour Fastness to Artificial Light: Xenon Arc Fading Lamp Test GB/T 8629-2001 Textiles - Domestic Washing and Drying Procedures for Textile Testing GB/T 8630 Textiles - Determination of Dimensional Change in Washing and Drying GB/T 14801 Test Method for Skewness and Bow in Woven and Knitted Fabrics GB/T 18132 Silk Garments GB 18401 National General Safety Technical Code for Textile Products GB/T 21294 Testing Methods of Physical and Chemical Performance of Garments GB/T 21295 Requirements of Physical and Chemical Performance of Garments GB/T 29862 Textiles - Identification of Fiber Content GB/T 31127-2014 Textiles - Tests for Colour Fastness - Colour Fastness to Transfer in Joints GB 31701 Safety Technical Code for Infants and Children Textile Products GB/T 31907 Method of Garment Measurement FZ/T 80002 Marking, Packaging Transportation and Storage for Garments FZ/T 80004 Rule for Garments Delivery Inspection FZ/T 80007.3 Dry Wash Resistance Test Method for Garments Used Adhesive Interlining Appearance defect Sample Photos for M&F Unlined Clothes and Clothes with Fillings and M&F Children's Unlined Clothes Sample Photo of Grade 5 Appearance Defects and Sewing Wrinkle of Down Garments 3 Requirements 3.1 Instructions for use Instructions for use shall be in accordance with those specified in GB 5296.4 and GB 31701. 3.2 Size specification 3.2.1 Size designation shall be in accordance with those specified in GB/T 1335 (all parts). 3.2.2 The specification of main parts is designed at discretion according to the relevant requirements of GB/T 1335 (all parts). 3.3 Raw materials 3.3.1 Fabric Fabrics conforming to the quality requirement of this standard are selected according to the relevant national standards regarding textile fabrics. 3.3.2 Lining Lining suitable for the applied fabric and conforming to the quality requirements of this standard shall be adopted. Air-proof film shall not be used. 3.3.3 Filling and materials of detachable lining Various natural fiber, chemical fiber and their blends with certain warmth retention property as well as animal fur and fake fur shall be selected and their quality shall meet the requirements of relevant laws and regulations, compulsory standards and relevant standards. 3.3.4 Accessories 3.3.4.1 Interlining, shoulder pad, decorative lace and bagging Interlining, shoulder pad, decorative lace and bagging suitable to the performance of the used fabric and lining shall be adopted and their quality shall meet the requirements of this standard. 3.3.4.2 Suture, drawstring and cord, elastic ribbon Suture, drawstrings and cords, elastic ribbon (expect ornamental thread and belt) suitable to the performance of the used fabric, lining and accessories shall be adopted. 3.3.5 Button, zipper and other accessories Button (except ornamental button), zipper and other accessories suitable for the used fabric shall be adopted. The button, ornamental button, zipper and other accessories shall be smooth on surface and free from burr, damage, defects and accessible sharp tip or edge. Zippers shall be good in meshing and run smoothly. Note: Accessible sharp tip or edge refers to any sharp edge or tip on finished product that may cause harm to human skin under normal wearing. 3.4 Wrap and weft yarn direction The front hem shall not upwarp; the yarn skewness degree of back, sleeve and front and rear trousers (skirt) pieces shall not be greater than 3%; the yarn skewness degree of yarn-dyed stripe and plaid shall not be greater than 2.5% (except for special design). 3.5 Strip matching and plaid matching 3.5.1 Fabric with obvious stripes and plaids of 1.0cm or above shall be in accordance with those specified in Table 1. Table 1 In: cm Part Requirements for strip matching and plaid matching Remarks Left and right front The strips are smooth and straight, plaids shall match each other horizontally and the mutual deviation shall not be greater than 0.3. If the sizes of strip and plaid are different, they shall be subject to the upper part of one third of the clothes length. Pocket, pocket flap and bodice Strips shall match with each other, plaids shall match with each other and the mutual deviation shall not be greater than 0.3. If the sizes of strip and plaid are different, they shall be subject to the center of the front of pocket. Collar point The strips are symmetrical and the mutual deviation shall not be greater than 0.3. For shadow strips and plaids, visible strips and plaids shall prevail. Sleeve The two sleeves shall be smooth and straight, strip and plaid shall be symmetrical by the sleeve cap and the mutual deviation shall not be greater than 1.0. —— Side seam of trouser and skirt Plaids shall match with each other horizontally at the positions 10.0 below the side seam pocket mouth, with mutual deviation not greater than 0.5. —— Front/back crotch seams Strip and plaid shall be symmetrical, plaids shall match with each other horizontally and the mutual deviation shall not be greater than 0.5. —— Note: Special design is excluded. 3.5.2 The grain direction of nip-up and down pile and checkerboard weave material is consistent all over the body, except for special design. 3.5.3 Fabrics with special pattern shall be subjected to the main drawing and the grain direction of the whole body shall be consistent. 3.6 Colour difference 3.6.1 The colour difference of top collar and pocket from the bodice shall be higher than Grade 4, that of side seams of trouser and skirt shall be higher than Grade 4 as well and that of other surface parts shall not be lower than Grade 4. 3.6.2 The colour difference influenced by interlining or caused by multilayer materials shall not be lower than Grades 3-4 (except for special design). 3.6.3 The colour difference between tops and bottoms of suits shall not be lower than Grade 4. 3.7 Appearance defects The defect permissibility for each part of finished product shall be in accordance with those specified in Table 2. The part classification of finished product is detailed in Figure 1. Only one kind of defect within permissibility is allowed at each part. The defects not covered in this standard shall be in accordance with the requirements for similar ones in Table 2 based on their forms. Table 2 Defect Permissibility at each part Part 1 Part 2 Part 3 Linear defect Not allowed Below 2.0cm in length Below 4.0cm in length Streak defect Not allowed Not allowed Below 1.5cm in length Color bar Not allowed Minor Having no influence on appearance Spots (oil, rust, colour spot) Not allowed Not obvious and no larger than 0.2cm 2 Not obvious and no larger than 0.2cm 2 Damaging defect Not allowed Not allowed Not allowed Spread defect Not allowed Not allowed Not allowed Note 1: Minor: not obvious visually and may be identified via careful identification. Obvious: having no influence on the overall effect but can be obviously felt. Note 2: The allowable value of both linear defect and strip/block defect in this table refers to the total dimension of similar defects on the same product. Note: Special design is excluded. Figure 1 3.8 Sewing 3.8.1 Stitch length density shall be in accordance with those specified in Table 3, except for special design. Table 3 Item Stitch length density Remarks Top and blind stitch Not less than 12 stiches/3cm Except for special needs Overlock stitch Not less than 9 stiches/3cm —— Basting yarn Not less than 9 stiches/3cm Except for decorative basting yarn Buttonhole Thin thread Not less than 12 stiches/1cm —— Thick thread Not less than 9 stitches/1cm —— Note: Thin thread refers to the sewing thread of 20 tex or below; thick thread refers to the sewing thread above 20 tex. 3.8.2 The stitching of all parts shall be flat, smooth, straight, regular and firm, with uniform stitches. Upper and lower threads are suitable in tightness and free from skipped or broken stitches and pinholes. The place with starting and ending stitches shall be sewed in close and straight stitches. The wrinkle and shrinkage degree in sewing shall not be lower than Grade 3 according to the requirements of Sample Photo of Grade 5 Appearance Defects and Sewing Wrinkle of Down Garments. 3.8.3 The collar shall be flat, smooth and not upturned; splicing and skipped stitches are not allowed for the top stitch in collar. Top collar, lining and interlining shall be flat and suitable in tightness. Padded coat with removable inner container, the back neck hole and collar extension of front facing shall have clean finish hem and be overlocked or bound. The removable inner container shall be flat and smooth in the connection with front facing. The inner container shall be suitable in tightness with the fabric and button placement shall be bilaterally symmetric. The height dislocation of removable inner container shall not be greater than 1.5cm. If natural fur is used, the grain direction of the rough selvedge and villus of removable cap section shall be consistent and the connection with cap section shall be straight, flat and smooth. 3.8.4 Setting in sleeve is even and smooth; and front and back of two sleeves are basically consistent. 3.8.5 The pockets shall match with the pocket flaps in size and shall be round, smooth and consistent in height. Both ends of pocket mouth shall be firm and inclined fabric shall be bilaterally symmetric. 3.8.6 Welt and batten shall be flat and smooth and be consistent in width. 3.8.7 Burr of the exposed seam allowance shall not be exposed.

Foreword i 1 Scope 2 Normative References 3 Requirements 5 Inspection Rules 6 Marking, Packaging, Transportation and Storage

棉服裝 1 范圍 本標準規定了棉服裝的要求、檢驗方法、檢驗規則以及標志、包裝、運輸和貯存。 本標準適用于以紡織機織物為主要面料，以各種天然纖維、化學纖維及其共混物等為填充物，或以動物毛皮、人造毛皮等為里或制成活里，成批生產的棉服裝。 本標準不適用于填充物中含有羽絨羽毛的產品。 本標準不適用于年齡在36個月及以下的嬰幼兒服裝。 2規范性引用文件 下列文件對于本文件的應用是必不可少的。凡是注日期的引用文件，僅注日期的版本適用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 GB/T 250紡織品 色牢度試驗 評定變色用灰色樣卡 GB/T 1335(所有部分)服裝號型 GB/T 3921—2008紡織品 色牢度試驗 耐皂洗色牢度 GB/T 4841.3染料染色標準深度色卡 2/1、1/3、1/6、1/12、1/25 GB 5296.4 消費品使用說明 第4部分：紡織品和服裝 GB/T 8170數值修約規則與極限數值的表示和判定 GB/T 8427—2008 紡織品 色牢度試驗 耐人造光色牢度；氙弧 GB/T 8629—2001紡織品 試驗用家庭洗滌和干燥程序 GB/T 8630紡織品 洗滌和干燥后尺寸變化的測定 GB/T 14801機織物與針織物緯斜和弓緯試驗方法 GB/T 18132絲綢服裝 GB 18401 國家紡織產品基本安全技術規范 GB/T 21294服裝理化性能的檢驗方法 GB/T 21295服裝理化性能的技術要求 GB/T 29862紡織品 纖維含量的標識 GB/T 31127—2014紡織品 色牢度試驗 拼接互染色牢度 GB 31701 嬰幼兒及兒童紡織產品安全技術規范 GB/T 31907服裝測量方法 FZ/T 80002服裝標志、包裝、運輸和貯存 FZ/T 80004服裝成品出廠檢驗規則 FZ/T 80007.3使用粘合襯服裝耐干洗測試方法 男女單、棉服裝、男女兒童單服裝外觀疵點樣照 羽絨服裝外觀疵點及縫制起皺五級樣照 3 要求 3.1 使用說明 使用說明按GB 5296.4和GB 31701規定。 3.2 號型規格 3.2.1 號型設置按GB/T 1335(所有部分)規定。 3.2.2主要部位規格按GB/T 1335(所有部分)有關規定自行設計。 3.3 原材料 3.3.1 面料 按國家有關紡織面料標準選用符合本標準質量要求的面料。 3.3.2 里料 采用與所用面料相適宜并符合本標準質量要求的里料。不允許使用不透氣薄膜。 3.3.3填充物，活里用料 應選用具有一定保暖性的各種天然纖維、化學纖維等及其共混物，以及動物毛皮，人造毛皮，其質量應符合有關法律法規、強制性標準及相關標準的要求。 3.3.4 輔料 3.3.4.1 襯布、墊肩、裝飾花邊、袋布 采用與所用面、里料的性能相適宜的襯布、墊肩、裝飾花邊、袋布，其質量應符合本標準規定。 3.3.4.2縫線、繩帶、松緊帶 采用與所用面、里料、輔料的性能相適宜的縫線、繩帶，松緊帶(裝飾線、帶除外)。 3.3.5鈕扣、拉鏈及其他附件 采用適合所用面料的鈕扣(裝飾扣除外)、拉鏈及其他附件。鈕扣、裝飾扣、拉鏈及其他附件應表面光潔，無毛刺、無缺損、無殘疵、無可觸及銳利尖端和銳利邊緣。拉鏈嚙合良好、光滑流暢。 注：可觸及銳利尖端和銳利邊緣是在正常穿著條件下，成品上可能對人體皮膚造成人身傷害的銳利邊緣和尖端。 3.4經緯紗向 前身底邊不允許倒翹，后身、袖子、前后褲(裙)片紗線歪斜程度不大于3％，色織條、格類紗線歪斜程度不大于2.5％(特殊設計除外)。 3.5對條對格 3.5.1 面料有明顯條格在1.0 cm及以上的接表1規定。 表1 單位為厘米 部位名稱 對條、對格規定 備 注 左右前身 條料順直，格料對橫，互差不大于0.3 條格大小不一時，以衣長三分之一的上部為主 袋、袋蓋與大身 條料對條，格料對格.互差不大于0.3 遇條格大小不一時，以袋前部的中心為主 表1(續) 單位為厘米 部位名稱 對條、對格規定 備 注 領尖 條料對稱，互差不大于0.3 陰陽條格以明顯條格為主 袖子 兩袖左右順直，條格對稱，以袖山為準，互差不大于1.0 褲、裙側縫 側縫袋口下10.0以下格料對橫，互差不大于0.5 前后襠縫 條格對稱，格料對橫，互差不大于0.5 注：特殊設計除外。 3.5.2 倒順毛絨、陰陽格原料，全身順向一致，特殊設計除外。 3.5.3 特殊圖案面料以主圖為準，全身順向一致。 3.6 色差 3.6.1 領面、袋與大身色差高于4級，褲、裙側縫色差高于4級，其他表面部位色差不低于4級。 3.6.2 襯布影響或多層料造成的色差不低于3-4級(特殊設計除外)。 3.6.3套裝的上裝與下裝的色差不低于4級。 3.7 外觀疵點 成品各部位的疵點允許存在程度按表2規定。成品各部位劃分見圖1。各部位只允許一種允許存在程度內的疵點。未列入本標準的疵點按其形態，參照表2相似疵點規定。 表2 疵點名稱 各部位允許存在程度 1號部位 2號部位 3號部位 線狀疵點 不允許 長2.0 cm以下 長4.0 cm以下 條狀疵點 不允許 不允許 長1.5 cm以下 色檔 不允許 輕微 不影響外觀 斑疵(油、銹、色斑) 不允許 不明顯，不大于0.2 cm2 不明顯，不大于0.2 cm2 破損性疵點 不允許 不允許 不允許 散布性疵點 不允許 不允許 不允許 注1：輕微——疵點在直觀上不明顯，通過仔細辨認才可看出。 明顯——不影響總體效果，但能明顯感覺到疵點的存在。 注2：表中線狀疵點和條塊狀疵點的允許值是指同一件產品上同類疵點的累計尺寸。 注3：特殊設計除外。 臀圍線 下襠 圖1 3.8 縫刺 3.8.1針距密度按表3規定，特殊設計除外。 表3 項 目 針距密度 備注 明暗線 不少于12計/3 cm 特殊需要除外 包縫線 不少于9針/3 cm 絎線 不少于9針/3 cm 裝飾絎線除外 鎖眼 細線 不少于12針/1 cm 粗線 不少于9針/1 cm 注：細線：20tex及以下縫紉線；粗線：20 tex以上縫紉線。 3.8.2各部位縫制平服，線路順直、整齊、牢固，針跡均勻。上下線松緊適宜，無跳線、斷線，無針眼，起止針處應緝牢。縫制皺縮程度按《羽絨服裝外觀疵點及縫制起皺五級樣照》規定，不低于3級。 3.8.3領子平服，不反翹，領子部位明線不允許有接線和跳針。領面、里、襯松緊適宜?？裳b卸內膽的棉上農，后托領圈與掛面外口，應折光邊、包縫或滾條?？裳b卸內膽與掛面結合部位平服，內膽與面料松緊適宜，扣位左右對稱，可裝卸內膽的左右高低錯位不大于1.5cm。使用天然毛皮，可裝卸的帽口毛邊，絨毛順向一致與帽口連接處應順直、平服。 3.8.4绱袖圓順，兩袖前后基本一致。 3.8.5袋與袋蓋大小適宜、方正、圓順、左右高低一致，袋口兩端應牢固，斜料左右對稱。 3.8.6滾條、壓條應平服、寬窄一致。 3.8.7外露縫份毛邊不外露。 3.8.8拉鏈緝線整齊，拉鏈平服、順直，左右高低一致，與拉合部位相符，松緊適宜。 3.8.9鎖眼定位準確，大小適宜?？裳b卸內膽的棉上衣，應在袖口內側、底邊左右擺縫的位置，有用于固定的鈕、袢或搭扣。 3.8.10扣與扣眼對位，整齊牢固?？勰_高低適宜，線結不外露。線結不應釘在單層布上(裝飾扣除外)，纏腳高度與鎖眼厚度相適宜，收線打結應結實完整，釘扣線不脫散。四合扣牢固，上下應對位，吻合適度，無變形，松緊適宜。 3.8.11 商標和耐久性標簽位置端正，平服。 3.8.12對稱部位基本一致。 3.8.13各部位30 cm內不應有連續跳針或一處以上單跳針，鏈?zhǔn)骄€(xiàn)跡不允許跳線。 3.8.14裝飾物(繡花、鑲嵌等)牢固、平服。 3.8.15絎線順直，厚薄均勻，表面絎線左右對稱，橫向絎線互差不大于0.4 cm。 3.9 規格尺寸允許偏差 成品主要部位規格尺寸允許偏差按表4規定。 表4 單位為厘米 部位名稱 規格尺寸允許偏差 成人 兒童 衣長 上衣 ±1.5 -1.5～+2.5 大衣 ±2.0 -1.5～+3.5 胸圍 ±3.0 -2.0～+4.0 領大 ±1.0 -0.8～+1.5 總肩寬 ±1.0 -0.8～+2.0 袖長 圓袖 ±1.0 -1.0～+2.0 連肩袖 ±1.5 -1.5～+2.5 褲、裙長 ±2.0 -1.5～+3.0 腰圍 ±1.5 -1.0～+2.0 3.10整燙 3.10.1 各部位熨燙平服、整潔，無燙黃、水漬及亮光。 3.10.2使用粘合襯部位不允許有脫膠、滲膠、起皺、起泡及沾膠。 3.11理化性能 成品理化性能按表5規定。 表5 項目 分等要求 優等品 一等品 合格品 纖維含量/％ 符合GB/T 29862規定 甲醛含量/(mg/kg) 符合GB 18401規定 pH值 可分解致癌芳香胺染料/(mg/kg) 異味 尺寸變化率a/％ ≥ 水洗b 胸圍 -1.5 -2.0 -2.5 衣長 -1.5 -2.5 -3.5 腰圍 -1.5 -2.0 -2.5 褲、裙長 -1.5 -2.5 -3.5 干洗c 胸圍 -2.0 衣長 -2.0 腰圍 -2.0 褲、裙長 -2.0 面料色牢度d/級 ≥ 耐皂洗b 變色 4 3-4 3 沾色 4 3-4 3 耐干洗c 變色 4-5 4 3-4 沾色 4-5 4 3 耐水 變色 3-4 3 3 沾色 3-4 3 3 耐汗?jié)n 變色 3-4 3 3 沾色 3-4 3 3 耐干摩擦 沾色 4 3-4 3 耐濕摩擦e 沾色 4 3-4 3 耐光 變色 4 3 3 拼接互染f 沾色 4-5 4 4 里料色牢度d/級 ≥ 耐皂洗h 沾色 3 耐干摩擦 3-4 耐水 符合GB 18401規定 耐汗?jié)n 表5(續) 項目 分等要求 優等品 一等品 合格品 接縫性能g 褲后襠縫接縫強力/N ≥ 符合GB/T 21295規定 縫子紕裂程度/cm 覆粘合襯部位剝離強力h/N ≥ 面料起球i/級 ≥ 4 3-4 3 洗滌后外觀 不允許出現破損、明顯變形和變色，復合、噴涂、印花以及繡花面料不能起泡、脫落或嚴重起皺，表面部位不能有明顯水漬，附件不允許脫落和銹蝕，里料不允許外露，填充物不允許出現縮團，不允許嚴重影響外觀及使用性能的其他變化 注：按GB/T 4841.3的規定，顏色深于1/12染料染色標準深度色卡為深色，顏色不深于1/12染料染色標準深度為淺色。 a尺寸變化率中，腰圍不考核松緊腰圍。 b水洗尺寸變化率、耐皂洗色牢度不考核使用說明中標注不可水洗的產品。 c干洗尺寸變化率、耐干洗色牢度不考核使用說明中標注不可干洗的產品。 d蠶絲纖維含量≥50％的織物色牢度允許程度按GB/T 18132的規定。 e起絨、磨毛、植絨類面料、深色面料的濕摩擦色牢度的合格品考核指標允許比本標準降半級。 f拼接互染色牢度只考核深、淺顏色拼接的產品，不考核使用說明中標注不可水洗的產品。 g外層僅起裝飾作用部分不考核接縫性能。 h覆粘合襯部位剝離強度只考核上衣的領子和大身部位，且不考核復合，噴涂面料的剝離，非織造布粘合襯如在 試驗中無法剝離則不考核此項目。 i起絨、磨毛、植絨類織物不考核起球。 3.12兒童服裝安全性能 36個月以上至14歲兒童穿著的棉服裝還應符合GB 31701的規定。 4檢驗方法 4.1 檢驗工具 4.1.1鋼卷尺或直尺，分度值為1 mm。 4.1.2紡織品 色牢度試驗 評定變色用灰色樣卡(GB/T 250)。 4.1.3 1/12染料染色標準深度色卡(GB/T 4841.3)。 4.1.4男女單、棉服裝、男女兒童單服裝外觀疵點樣照。 4.1.5羽絨服裝外觀疵點及縫制起皺五級樣照。 4.2 規格測定 主要部位的測量方法按GB/T 31907規定。 4.3 外觀測定 4.3.1 外觀檢驗一般采用燈光照明，照度不低于600 lx，有條件時也可采用北空光照明。 4.3.2評定色差程度時，被評部位應紗向一致。入射光與織物表面約成45°角，觀察方向應垂直于織物表面，距離60 cm目測，與GB/T 250樣卡對比。 4.3.3外觀疵點允許存在程度測定時，距離60 cm目測，并與男女單、棉服裝、男女兒童單服裝外觀疵點樣照對比，必要時采用鋼卷尺進行測量。