標準編號:	QC/T 1011-2023
中文名稱:	汽車離合器總泵
英文名稱:	Clutch master cylinder of automobile
中標分類:	T21    傳動系統
行業分類:	QC    汽車行業標準
ICS分類:	43.040.50 43.040.50    傳動裝置、懸掛裝置 43.040.50
發布機構:	中華人民共和國工業和信息化部
發布日期:	2023-4-21
實施日期:	2023-11-1
標準狀態:	valid
替代舊標準:	QC/T 1011-2015 離合器液壓氣助力系統總泵技術要求和臺架試驗方法
翻譯語言:	英文
文件格式:	PDF
中文字符數:	22000 字
翻譯價格(元):	1540.0
交付時間:	付款后 1~5 個工作日

Clutch master cylinder of automobile 1 Scope This document specifies the terms and definitions, technical requirements, and test methods of clutch master cylinder of automobile (hereinafter referred to as the "master cylinder"). This document is applicable to the clutch master cylinder of automobile. 2 Normative references The following documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 10125 Corrosion tests in artificial atmospheres - Salt spray tests GB 12981 Motor vehicle brake fluids GB/T 41481 Road vehicles - Cleanliness of components and systems QC/T 307 Performance requirements and bench test methods of vacuum booster for automobile QC/T 1125 Automotive clutch terminology and definition 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 maximum stroke distance that the piston moves from its initial position to its limit position 3.2 initial pressure-building travel distance that the piston moves from its initial position to the position where the pressure of hydraulic chamber is 0.1MPa 3.3 ideal stroke distance that the piston moves from its initial position to the position where the channel (such as the center valve or compensating hole) between the storage chamber and the hydraulic chamber of the master cylinder begins to close 3.4 the point of initial assistant force downward turning point of the characteristic line under different air source pressures in the input-output characteristic curve of a master cylinder with assistance force 3.5 the point of maximal assistant force upward turning point of the characteristic line under different air source pressures in the input-output characteristic curve of a master cylinder with assistance force 4 Product classification Master cylinders are classified into three types by structural forms: Classes A, B and C. Class A is hydraulic master cylinder, as shown in Figure 1; Class B is air-assistant master cylinder, as shown in Figure 2; Class C is vacuum-assistant master cylinder, as shown in Figure 3.

Contents Foreword II 1 Scope 2 Normative references 3 Terms and definitions 4 Product classification 5 Technical requirements 6 Test methods

汽車離合器總泵 1 范圍 本文件界定了汽車離合器總泵(以下簡稱“總泵”)的術語和定義，規定了總泵的技術要求和試驗方法。 本文件適用于汽車離合器總泵。 2 規范性引用文件 下列文件中的內容通過文中的規范性引用而構成本文件必不可少的條款。其中，注日期的引 用文件，僅該日期對應的版本適用于本文件；不注日期的引用文件，其最新版本(包括所有的修改單)適用于本文件。 GB/T 10125 人造氣氛腐蝕試驗 鹽霧試驗 GB 12981 機動車輛制動液 GB/T41481 道路車輛 零部件和系統的清潔度 QC/T307 汽車用真空助力器性能要求及臺架試驗方法 QC/T1125 汽車離合器系統術語及定義 3 術語和定義 下列術語和定義適用于本文件。 3.1 最大行程 maximum stroke 活塞從初始位置運動到極限位置之間的距離。 3.2 初始建壓行程 initial pressure-building travel 活塞從初始位置運動到液壓腔產生0.1MPa 壓力時位置的距離。 3.3 空行程 ideal stroke 活塞從初始位置至總泵儲液腔與液壓腔之間通道(如中心閥門或補償孔)開始關閉位置所移動的距離。 3.4 初始助力點 the point of initial assistant force 帶助力總泵的輸入-輸出特性曲線中，不同氣源壓力下特性線的下折點。 3.5 最大助力點 the point of maximal assistant force 帶助力總泵的輸入-輸出特性曲線中，不同氣源壓力下特性線的上折點。 4 產品分類 按總泵結構形式，分為三類： A 類、B 類和C 類。A 類為液壓總泵見圖1,B 類為氣助力總泵見 圖 2 ,C 類為真空助力總泵見圖3。