標準編號:	GB/T 14295-2019
中文名稱:	空氣過濾器
英文名稱:	Air filter
中標分類:	P48    通風、空調工程
行業分類:	GB    國家標準
ICS分類:	91.140.30 91.140.30    通風和空調系統 91.140.30
發布機構:	國家市場監督管理總局 國家標準化管理委員會
發布日期:	2019-06-04
實施日期:	2020-5-1
標準狀態:	valid
替代舊標準:	GB/T 14295-2008 空氣過濾器
翻譯語言:	英文
文件格式:	PDF
中文字符數:	25000 字
翻譯價格(元):	1500.0
交付時間:	付款后 1 個工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. SAC/TC 143 is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. This standard is developed in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 14295-2008 Air filters, and the following main technical changes have been made with respect to GB/T 14295-2008: ——Product classification and designation methods are modified; ——The requirements and test methods for the cleaning efficiency for PMx efficiency are added; ——The requirements and test methods for rated power and working voltage of electric air filter are added; ——The requirements for the ozone concentration increment limit of electric air filter are modified; ——The requirements for test instruments are added; ——The requirements for the performance of test devices for air filter are added; ——The test method for electrostatic elimination of air filter is added; ——The requirements for standard test dust for dust holding capacity test of air filter are modified and the dust holding capacity limit is added. This standard was proposed by the Ministry of Housing and Urban-Rural Development of the People's Republic of China. This standard is under the jurisdiction of the National Technical Committee on HVAC and Purification Equipment of Standardization Administration of China (SAC/TC 143). The previous editions of this standard are as follows: ——GB/T 14295-1993 and GB/T 14295-2008. Air filter 1 Scope This standard specifies terms and definitions, classification and designation, general requirements, requirements, test methods, inspection rules as well as marking, packaging, transportation and storage of air filters. This standard is applicable to air filters for ventilation, air conditioning and air purification systems or equipment. This standard is not applicable to high-efficiency air filters or superior ones. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the normative document (including any amendments) applies. GB/T 191 Packaging - Pictorial marking for handling of goods GB/T 1019 General requirements for the package of household and similar electrical appliances GB/T 1236 Industrial fans - Performance testing using standardized airways GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB 4706.1 Household and similar electrical appliances - Safety- Part 1: General Requirements GB 8624 Classification for burning behavior of building materials and products GB/T 18204.2 Examination methods for public places - Part 2: Chemical pollutants GB 50243 Code of acceptance for construction quality of ventilation and air conditioning works JG/T 404 Air filter media 3 Terms and definitions For the purpose of this standard, the following terms and definitions apply. 3.1 air filter the equipment for removing particulate matters (PMs) in the air by filtration, adhesion, charge trapping, etc. 3.2 electric air filter a type of air filter for removing the PMs in the air by using dust collection plate to trap the PMs which have been charged by applying high-voltage electrostatic field 3.3 rated air flow the volume flow of air passing through the air filter in nominal unit time under standard air condition 3.4 face velocity the ratio of the volume flow rate of air passing through the air filter vertically to the area of the section for ventilation 3.5 initial resistance the static pressure loss of air filter operating at rated air flow in initial state 3.6 final resistance a specified static pressure loss value reached by the air filter after increasing due to collection of standard test dust at rated air flow 3.7 particle size geometrical diameter of PMs measured by optical or aerodynamic equivalent methods 3.8 efficiency the capacity of air filter for removing PMs in the circulating air at rated air flow, i.e. the ratio of the concentration difference between PMs at the upwind side and downwind side to the concentration of PMs at the upwind side 3.9 counting efficiency the efficiency of the air filter to remove PMs with particular optical particle size or particle size range in the circulating air at rated air flow 3.10 arrestance efficiency the efficiency of air filter to remove the standard test dust in circulating air at rated air flow in mass 3.11 cleaning efficiency for PMx the efficiency of air filter to remove the PMs with aerodynamic equivalent particle size less than or equal to x μm in the circulating air at rated air flow in mass 3.12 dust holding capacity the total mass of standard test dust collected where the air filter reaches final resistance at rated air flow 3.13 rated power the input power of electric air filter working at rated air flow in initial state 3.14 working voltage the ionization voltage and the dust collection voltage of the electric air filter during working in the initial state 4 Classification and designation 4.1 Classification 4.1.1 According to the efficiency level, air filters can be classified into low efficiency filter, medium efficiency filter, high-medium efficiency filter and sub-high efficiency filter, coded as C, Z, GZ and YG respectively. Among them, the low efficiency filters can be classified into low efficiency 1 ones, low efficiency 2 ones, low efficiency 3 ones and low efficiency 4 ones, coded as C1, C2, C3 and C4 respectively. The medium efficiency filters can be classified into medium efficiency 1 ones, medium efficiency 2 ones and medium efficiency 3 ones, coded as Z1, Z2 and Z3 respectively. 4.1.2 According to the structure type, air filters can be classified into flat-plate type, bag type, pleated type, moving curtain type, cartridge type, pole plate type and honeycomb type, coded as PB, DS, ZZ, JR, TS, JB and FC respectively. 4.2 Designation Example 1: An air filter of medium efficiency 2, bag type, with overall dimension of 592 mm×592 mm×600 mm and rated air flow of 3,400 m3/h, designated as K-Z2-DS-592×592×600-3400. Example 2: An air filter of low efficiency 3, flat-plate type, with overall dimension of 610 mm×610 mm×80 mm and rated air flow of 2,000 m3/h, designated as K-C3-PB-610×610×80-2000. Note: The representation principle for overall dimension of filters: with air flow direction as the depth, and the vertical length and the horizontal length of the section perpendicular to the air flow direction as height and width respectively. 5 General requirements 5.1 The application of air filters shall meet the environmental protection and fire resistance requirements of the site. 5.2 Electric air filters shall meet the following requirements: a) Single-phase rated voltage shall not be greater than 250 V, three-phase rated voltage shall not be greater than 480 V and the rated frequency shall be 50 Hz; b) Power-off protection shall be arranged to ensure automatic power-off of internal devices during repair or maintenance after opening unit structure; c) The electrical safety performance shall meet the relevant requirements of GB 4706.1. 5.3 Air filter media shall meet the relevant requirements of JG/T 404. 5.4 The shear strength and tensile strength of binders for air filter shall not be less than those of the media; and the temperature resistance of binders shall be the same as that of the media. 5.5 The sealant for air filters shall be able to ensure that the filters are free from crack and degumming with elasticity during operation at maximum operating air flow or final resistance, and the temperature resistance and humidity resistance of the sealant shall be the same as those of the media.

Foreword I 1 Scope 2 Normative references 3 Terms and definitions 4 Classification and designation 5 General requirements 6 Requirements 7 Test methods 8 Inspection rules 9 Marking, packaging, transportation and storage Annex A (Normative) Test methods for resistance, counting efficiency and cleaning efficiency for PMx of air filter Annex B (Normative) Test methods for arrestance efficiency and dust holding capacity of air filter Annex C (Normative) Test method for electrostatic elimination of air filter Annex D (Normative) Test method for ozone concentration increment of electric air filter

空氣過濾器 1 范圍 本標準規定了空氣過濾器的術語和定義、分類與標記、一般要求、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。 本標準適用于通風、空氣調節和空氣凈化系統或設備用空氣過濾器。 本標準不適用于高效及以上級別的空氣過濾器。 2 規范性引用文件 下列文件對于本文件的應用是必不可少的。凡是注日期的引用文件，僅注日期的版本適用本文件。凡是不注日期的引用文件，其最新版本（包括所有的修改單）適用于本文件。 GB/T 191 包裝儲運圖示標志 GB/T 1019 家用和類似用途電器包裝通則 GB/T 1236工業通風機用標準化風道性能試驗 GB/T 2828.1 計數抽樣檢驗程序 第1部分：按接收質量限(AQL)檢索的逐批檢驗抽樣計劃 GB 4706.1家用和類似用途電器的安全 第1部分：通用要求 GB 8624建筑材料及制品燃燒性能分級 GB/T 18204.2公共場所衛生檢驗方法 第2部分：化學污染物 GB 50243 通風與空調工程施工質量驗收規范 JG/T 404空氣過濾器用濾料 3 術語和定義 下列術語和定義適用于本文件。 3.1 空氣過濾器air filter 采用過濾、粘附或荷電捕集等方法去除空氣中顆粒物的設備。 3.2 靜電式空氣過濾器 electric air filter 采用高壓靜電場使顆粒物荷電之后，再被集塵板捕集的以實現去除空氣中顆粒物含量的空氣過濾器。 3.3 額定風量 rated air flow 在標準空氣狀態下，空氣過濾器在標稱的單位時間內通過的空氣體積流量。 3.4 迎面風速 face velocity 垂直通過空氣過濾器的空氣體積流量與其空氣流通截面面積之比。 3.5 初阻力initial resistance 在初始狀態下，空氣過濾器在額定風量下的靜壓損失。 3.6 終阻力 final resistance 在額定風量下，空氣過濾器由于捕集標準試驗塵而使其靜壓損失上升并達到的規定值。 3.7 粒徑 particle size 采用光學或空氣動力學等效方法測出的顆粒物幾何直徑。 3.8 效率efficiency 在額定風量下，空氣過濾器去除流通空氣中顆粒物的能力，即空氣過濾器上、下風側氣流中顆粒物濃度之差與上風側氣流中顆粒物濃度之比。 3.9 計數效率counting efficiency 在額定風量下，空氣過濾器去除流通空氣中特定光學粒徑或粒徑范圍的顆粒物數量的效率。 3.10 計重效率arrestance efficiency 在額定風量下，空氣過濾器去除流通空氣中標準試驗塵質量的效率。 3.11 PMx凈化效率cleaning efficiency for PMx 在額定風量下，空氣過濾器去除流通空氣中空氣動力學當量粒徑小于等于xμm的顆粒物質量的效率。 3.12 容塵量 dust holding capacity 在額定風量下，空氣過濾器達到終阻力時所捕集的標準試驗塵總質量。 3.13 額定功率rated power 在初始狀態下，靜電式空氣過濾器在額定風量下工作時的輸入功率。 3.14 工作電壓 working voltage 在初始狀態下，靜電式空氣過濾器工作時的電離電壓和集塵電壓。 4 分類與標記 4.1分類 4.1.1 按效率級別分為粗效過濾器、中效過濾器、高中效過濾器和亞高效過濾器，代號分別為C、Z、GZ和YG。其中粗效過濾器分為粗效1型、粗效2型、粗效3型和粗效4型，代號分別為C1、 C2、 C3和 C4；中效過濾器分為中效1型、中效2型和中效3型，代號分別為Z1、 Z2和 Z3。 4.1.2 按結構類型分為平板式、袋式、折褶式、卷繞式、筒式、極板式和蜂巢式，代號分別為PB、DS、ZZ、JR、TS、JB和FC。 4.2標記 示例1：中效2型、袋式、外形尺寸為592mm×592mm×600mm、額定風量為3400m3/h的空氣過濾器，標記為K-Z2-DS-592×592×600-3400。 示例2：粗效3型、平板式、外形尺寸為610mm×610mm×80mm、額定風量為2000m3/h的空氣過濾器，標記為K-C3-PB-610×610×80-2000。 注：空氣過濾器外形尺寸表示原則為：以氣流通過方向?yàn)樯疃龋詺饬魍ㄟ^(guò)方向垂直截面的豎直長度為高度、水平長度為寬度。 5 一般要求 5.1空氣過濾器的應用應滿足所用場合的環保及防火性要求。 5.2靜電式空氣過濾器應符合以下規定： a) 單相額定電壓不應大于250V，三相額定電壓不應大于480V，額定頻率應為50Hz； b) 應設置斷電保護，保證在打開機組結構進行維修或維護時，其內部裝置自動斷電； c) 電氣安全性能應滿足GB 4706.1的相關要求； 5.3空氣過濾器用濾料應滿足JG/T 404的相關要求。 5.4空氣過濾器用粘結劑的剪力強度和拉力強度不應低于所用濾料強度，其耐溫耐濕性能應與所用濾料相同。 5.5空氣過濾器用密封膠應能保證過濾器在最大運行風量或終阻力條件下，運行時不開裂、不脫膠，且有彈性，其耐溫耐濕性能應與所用濾料相同。 5.6空氣過濾器的結構應符合以下規定： a) 框架或支撐體應有滿足要求的強度和剛度，應能承受安裝、運行和維修時所需重量和壓力； b) 邊框的四個角和拼接處不應松動和開裂，濾料在邊框中不應松動和變形； c) 密封墊與邊框應粘結牢固，密封墊的內外邊緣不應超過邊框的內外邊緣。 6 要求 6.1外觀 6.1.1 空氣過濾器表面應光潔平整，無劃痕、銹斑、壓痕和損傷。 6.1.2 濾料、密封墊、防護網等部件不應變形。 6.1.3 靜電式空氣過濾器外殼應標明電氣安全警示及電氣端子接線圖。 6.2尺寸偏差 6.2.1外形尺寸 外形尺寸允許偏差見表1。 表1 外形尺寸允許偏差 單位為毫米 外形 類別 粗效過濾器 中效過濾器 高中效過濾器 亞高效過濾器 端面 ≤500 0 -1.6 >500 0 -3.2 深度 --- +1.6 0 每端面兩 對角線之差 ≤700 --- ≤2.3 >700 --- ≤4.5 6.2.2平面度 亞高效過濾器端面及側板平面度不應大于1.6mm。 6.3阻力和效率 6.3.1 在初始狀態下，空氣過濾器阻力、計重效率和計數效率應符合表2的規定。 表2 空氣過濾器額定風量下的阻力和效率 效率級別 指標 代號 迎面 風速 m/s 額定風量下 的效率（E） % 額定風量下的初阻力（ΔPi） Pa 額定風量下的終阻力（ΔPf） Pa 粗效1 C1 2.5 標準試驗塵計重效率 50>E≥20 ≤50 200 粗效2 C2 E≥50 粗效3 C3 計數效率 （粒徑≥2.0μm） 50>E≥10 粗效4 C4 E≥50 中效1 Z1 2.0 計數效率 （粒徑≥0.5μm） 40>E≥20 ≤80 300 中效2 Z2 60>E≥40 中效3 Z3 70>E≥60 高中效 GZ 1.5 95>E≥70 ≤100 亞高效 YG 1.0 99.9>E≥95 ≤120 6.3.2對于標稱PMx凈化效率的產品，其標稱效率值與實測效率值之差不應大于5%。 6.4容塵量 空氣過濾器應標稱容塵量指標，其實測值不應小于標稱值的90%，且不宜小于36mg/（m3/h）。 6.5清洗 可清洗的空氣過濾器清洗后的效率不應小于清洗前效率的85%，阻力不應大于清洗前阻力的150%。 6.6消靜電 對于濾料荷電的空氣過濾器，應標稱消靜電處理后的效率，其標稱效率值與實測效率值之差不應大于5%。 6.7防火 當空氣過濾器有防火要求時，應符合GB 8624的相關規定。 6.8額定功率 對于標稱值不大于30W的靜電式空氣過濾器，實測值不應大于標稱值的120%；對于標稱值大于30W的靜電式空氣過濾器，實測值不應大于標稱值的110%。 6.9工作電壓 對于靜電式空氣過濾器的電離電壓和集塵電壓，實測值與標稱值的偏差應在±5%范圍內。 6.10臭氧濃度增加量 在額定風量、工作電壓下，靜電式空氣過濾器臭氧濃度增加量1h均值不應大于0.05mg/m3。 6.11電氣安全 6.11.1電氣強度 靜電式空氣過濾器施加試驗電壓后，應無擊穿或閃絡。 6.11.2泄漏電流 靜電式空氣過濾器外露金屬部分和電源線間的冷態泄漏電流值不應大于0.75mA（Ⅰ類）或0.25 mA（Ⅱ類）。 6.11.3接地電阻 靜電式空氣過濾器外露金屬部分與接地端之間的電阻值不應大于0.1Ω。 7 試驗方法 7.1試驗儀表 試驗儀表應符合表3的規定。 表3 試驗儀表 測量參數 測量?jī)x表 測量項目 儀表性能要求 外形尺寸 游標卡尺 端面、深度、對角線長度 分度值：0.1mm 平面度 塞尺 端面及側板平面度 平板精度：2級； 塞尺厚度范圍：0.02 mm ~0.50mm 風量 空氣流量計 試驗風量 準確度：±3%讀數值 風速 風速儀 試驗風速 準確度：±3%讀數值， 分度值：0.01m/s 阻力 壓力計 初阻力和終阻力 0 Pa～70 Pa時，準確度：±2 Pa； >70 Pa時，準確度：±3%讀數值 計數效率 粒子計數器 計數濃度 粒子濃度示值誤差不超過±30% PMx凈化 效率 粉塵儀 PMx質量濃度 示值誤差不超過±20%， 示值重復性不應大于±10% 容塵量、計重效率 電子天平 空氣過濾器和末端過濾器發塵前后的質量、標準試驗塵的質量 分度值：0.1g 電氣強度 電安測試儀 靜電式空氣過濾器絕緣電阻、電氣強度、泄漏電流和接地電阻 接地電阻準確度：±3%讀數值； 泄漏電流準確度：±(3%讀數值+50μA)； 交流耐壓準確度：電壓指標±(3%讀數值+10V)，電流指標±(3%讀數值+30μA) 泄漏電流 接地電阻 工作電壓 萬用表 （帶高壓測試棒） 靜電式空氣過濾器的電離電壓和集塵電壓 準確度：±2%讀數值 功率 功率計 靜電式空氣過濾器的額定功率 精度：0.5級 臭氧濃度增加量 臭氧分析儀 臭氧濃度 準確度：±4%讀值 分光光度計 具有610nm波長和2cm比色皿 溫度 溫濕度計 試驗風道中的空氣溫度和相對濕度 準確度：±0.3℃ 相對濕度 準確度：±5% 大氣壓 大氣壓表 大氣壓 準確度：±2hPa 7.2外觀 應用目測法檢查。 7.3尺寸偏差 7.3.1外形尺寸 應用游標卡尺檢查。 7.3.2平面度 應用平板和塞尺檢查。 7.4阻力和效率 阻力、計數效率和PMx凈化效率應按附錄A規定的方法進行試驗，計重效率應按附錄B規定的方法進行試驗。 7.5容塵量 容塵量應按附錄B規定的方法進行試驗。 7.6清洗 清洗應按制造廠給出的清洗方法進行，清洗后的效率和阻力應按附錄A或附錄B規定的方法進行試驗。 7.7消靜電 消靜電應按附錄C規定的方法進行試驗，消靜電后的效率和阻力應按附錄A規定的方法進行試驗。 7.8防火 有防火要求的空氣過濾器，應按GB 8624規定的方法進行防火試驗。 7.9額定功率 靜電式空氣過濾器額定功率應按GB 4706.1規定的方法進行試驗。 7.10工作電壓 靜電式空氣過濾器的工作電壓應按GB 4706.1規定的方法進行試驗。 7.11臭氧濃度增加量 臭氧濃度增加量應按附錄D規定的方法進行試驗。 7.12電氣安全 7.12.1電氣強度 電氣強度應按GB 4706.1規定的方法進行試驗。 7.12.2泄漏電流 泄漏電流應按GB 4706.1規定的方法進行試驗。 7.12.3接地電阻 接地電阻應按GB 4706.1規定的方法進行試驗。 8檢驗規則 8.1檢驗分類 空氣過濾器的檢驗分為出廠檢驗和型式檢驗。 8.2出廠檢驗 8.2.1空氣過濾器應經制造廠質量檢驗部門檢驗合格后方可出廠。 8.2.2出廠檢驗應按表4的規定逐項進行。